Kymco Xciting 250i - Owner's Manual > Washing your scooter

1. Rinse the scooter thoroughly with cool water to remove any loose dirt.

2. Clean the scooter with a sponge or soft cloth using cool water.

Avoid directing water at muffler outlets and electrical parts.

3. Clean the plastic parts using a cloth or sponge dampened with a solution of mild detergent and water. Rub the soiled area gently rinsing it frequently with fresh water. Take care to keep brake fluid or other chemical solvents away from the scooter, as they will damage the plastic and painted surfaces.

NOTE: The inside of the headlight lens may be clouded immediately after washing the scooter. Moisture condensation inside the headlight lens will disappear gradually by heat from the headlight. After washing, run the engine while keeping the headlight on to dissipate the condensation.

4. After cleaning, rinse the scooter thoroughly with plenty of clean water. This rinsing is required to remove detergent residue can corrode alloy parts.

5. Dry the scooter and then start the engine, and let it run for several minutes.

6. Test the brakes before riding the scooter. Several applications of the brakes may be necessary to restore normal braking performance.

NOTE: Due to water on the brake components, braking efficiency may be temporarily impaired immediately after washing the scooter. Anticipate longer stopping distance to avoid a possible accident.

Finishing touches:

After washing your scooter, consider using a commerciallyavailable spray cleaner/polish or a quality liquid or paste wax to enhance and protect the paint's finish. Use only a non-abrasive polish or wax made specifically for scooters, motorcycles, or automobiles. Apply the polish or wax according to the instructions on the container.

Clean the windshield

Using plenty of water, clean the windshield with a soft cloth or sponge (avoid using detergents or any kind of chemical cleaner on the windshield). Dry the windshield with a soft, clean cloth.

To avoid possible scratching or other damage, use only water and a soft cloth or sponge to clean the windshield.

For a dirtier windshield, use a diluted neutral detergent with a sponge and plenty of water. Make sure to rinse off all the detergent.

(Detergent residue may cause windshield cracks.) Replace the windshield if scratches cannot be removed and they obstruct clear vision.

Do not let battery fluid, brake fluid or other acid chemicals contact the windshield body trim as they will damage the plastic.

Removing road salt

The salt used in some communities to prevent road icing can become very corrosive to your scooter. Wash your scooter as soon as possible if it comes in contact with road salt (or sea water).

1. Clean the scooter using cool water. Do not use warm water; as this will increase the corrosive effect of the salt.

2. Dry the scooter and protect painted and metal surfaces with wax or polish.

Painted aluminum wheel maintenance

Even if protected by paint, aluminum may corrode from contact with dirt, mud, or road salt. Clean the scooter's wheels with a wet sponge and mild detergent. Avoid stiff brushes, steel wool, or cleaners containing abrasives or chemical compounds.

After washing, rinse with plenty of water and dry with a clean cloth . Apply touch-up paint to the wheels where damage has occured.

Exhaust pipe maintenance

The exhaust system is stainless steel, but it can become stained by oil or mud. If necessary, remove heat stains with a liquid kitchen-counter abrasive.

STORAGE GUIDE

Extended storage, such as for the winter months, requires that you take certain steps to reduce the effects of deterioration from the non-use of your scooter. Whenever possible, perform any necessary periodic maintenance or repairs before storage so the scooter will be in good condition for riding when it is removed from storage.

Storage

1. Change the engine oil and filter.

2. Make sure the cooling system is filled with a 50/50% antifreeze solution.

3. Drain the carburetor (if equipped) and empty the fuel tank into an approved gasoline container using a commercially available hand siphon or an equivalent method. Spray the inside of the tank with an aerosol rust-inhibiting oil. Close the fuel filler cap on the fuel tank

Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Refuel the scooter outdoors and wipe up any spills immediately.

4. To prevent rusting in the cylinders, perform the following:

Remove the spark plug cap from the spark plug, and use tape or string to secure the caps to any convenient plastic body part so that they are positioned away from the spark plugs.

Remove the spark plugs from the engine and store them in a safe, dry place. Do not connect the spark plugs to the spark plug caps.

Pour a tablespoon (15 - 20 cc) of clean engine oil into each cylinder and cover the spark plug holes with a piece of cloth.

Crank the engine several times to distribute the oil.

Reinstall the spark plugs and spark plug caps.

5. Remove the battery. Store it in an area protected from freezing temperatures and direct sunlight. Slow charge the battery once a month (use a quality charger designed for use on a maintenance-free type battery).

6. Wash and dry the scooter. Wax all painted surfaces. Coat the chrome or bare aluminum parts with rust inhibiting oil.

7. Inflate the tires to their recommended pressures. Place the scooter on blocks to raise both tires off the ground.

8. Cover the scooter (don't use plastic or other coated materials) and store in an unheated area, free of excessive moisture, with a minimum of daily temperature variation. Do not store the scooter in direct sunlight as the sun's UV rays can damage the body work and other components.

Removal from storage

1. Uncover and clean the scooter.

2. Change the engine oil if more than 1 month has passed since the start of storage.

3. Charge the battery as required (use a quality charger designed for use on a maintenance-free type battery). Install the battery.

4. Drain any excess aerosol rust-inhibiting oil from the fuel tank. Fill the fuel tank with fresh gasoline.

5. Perform all the pre-ride inspection checks.

Test ride the scooter at low speeds in a safe riding area, away from traffic.

SPECIFICATIONS - XCITING 500i & 500Ri

Dimensions

Overall length .......................................... 2250 mm (90 in)
Overall width ........................................... 815 mm (32.6 in)
Overall height .......................................... 1450 mm (58 in)
Wheel base ............................................. 1570 mm (62.8 in)

Weight

Dry weight ............................................... 215 kg (473 lbs)

Capacities

Engine oil (after draining) ..................... 2.1 US qt (2.0 L)
(after draining & oil filter change) ......... 2.1 US qt (2.0 L)
(after disassembly) .................................. 2.7 US qt (25 L)

Transmission oil (after draining)............. 0.48 USqt (0.45 L)
(after disassembly) ............................... 0.57 US qt (0.5 L)

Fuel tank .............................................. (3.38 US gal, 12.8L )
Maximum weight capacity ..................... 150 kg (330 lbs)

Engine

Bore and stroke .............................................. 92 X 75 mm
Compression ratio .................................................... 10.5:1
Displacement .................................. 498.5 cm3 (30.4 cu-in)
Spark plug ................................................................ CR7E
Idle speed ...................................... 1300-1500 min-1 (rpm)

Chasis

Tire size, front ..................................................... 120/70-15
Tire size, rear ...................................................... 150/70-14

Electrical

Battery................................................................. 12v-12Ah
Headlight................................................. 12v60W/12v55W
Tail/brake light ............. 12v-0.47W LED & (12v4.4W LED)
Turn signal light .............................................. 12v10W X 4
Position light .......... 12v5W (front) & 12v0.47W LED (rear)

Fuses

Main fuse ..................................................................... 30A
Other fuses ........................................................... 10A, 15A

SPECIFICATIONS - XCITING 250/300i & 250/300Ri

Dimensions

Overall length .......................................... 2250 mm (90 in)
Overall width .......................................... 815 mm (32.6 in)
Overall height .......................................... 1450 mm (58 in)
Wheel base ........................................... 1570 mm (62.8 in)

Weight

Dry weight ............................................... 185 kg (407 lbs)

Capacities

Engine oil (after draining) ................... 0.95 US qt (0.9 L)
(after draining & oil filter change) ......... 1.2 US qt (1.1 L)

Transmission oil (after draining)......... 0.2 US qt (0.18 L)
(after disassembly) ........................... 0.25 US qt (0.23 L)

Fuel tank ......................................... (3.38 US gal, 12.8L )
Maximum weight capacity ..................... 150 kg (330 lbs)

Engine (250i & 250Ri)

Bore and stroke .......................................... 72.7 X 60 mm
Compression ratio ................................................... 10.6:1
Displacement .................................... 249 cm3 (15.2 cu-in)
Spark plug ........................................................ DPR6EA-9
Idle speed ...................................... 1500-1700 min-1 (rpm)

Engine (300i & 300Ri)

Bore and stroke ....................................... 72.7 X 65.2 mm
Compression ratio ................................................... 10.6:1
Displacement .................................... 270 cm3 (16.5 cu-in)
Spark plug ........................................................ DPR6EA-9
Idle speed ...................................... 1500-1700 min-1 (rpm)

Chasis

Tire size, front .................................................... 120/70-15
Tire size, rear ...................................................... 150/70-14

Electrical

Battery................................................................. 12v-12Ah
Headlight................................................. 12v60W/12v55W
Tail/brake light ............ 12v-0.47W LED & (12v4.4W LED)
Turn signal light ............................................. 12v10W X 4
Position light ....... 12v5W (front) & 12v0.47W LED (rear)

Fuses

Main fuse ........................................................... 30A
Other fuses .......................................................... 10A, 15A

See also: